欢迎来到中科聚峰机械有限公司!

24小时服务热线:

400-879-1999

点击拨打服务热线:400-879-1999
当前位置:首页>新闻中心>公司动态自上料搅拌车在清洗时有哪三个禁止事项?

自上料搅拌车在清洗时有哪三个禁止事项?

来源:http://www.jfhntjbj.com/ 日期:2021-08-06 发布人:admin
概述:在自上料搅拌车的车轮维修中,少数搅拌车司机为了防止车轮上螺栓螺母生锈,安装时别出心裁地将螺栓螺母都涂上润滑油,殊不知这种做法不仅错误,而且给自上料搅拌车行车安 全带来一定
在自上料搅拌车的车轮维修中,少数搅拌车司机为了防止车轮上螺栓螺母生锈,安装时别出心裁地将螺栓螺母都涂上润滑油,殊不知这种做法不仅错误,而且给自上料搅拌车行车安 全带来一定的隐患。螺栓和螺母拧紧后,相互间具有自锁的特性。而涂上润滑油后,二者之间的自锁系数变小、自锁性能下降。在自上料搅拌车高速行驶时,螺栓螺母很容易松动乃脱落,从而引发自上料搅拌车行车事故。
In the wheel maintenance of self loading mixer truck, in order to prevent the bolts and nuts on the wheel from rusting, a few mixer truck drivers apply lubricating oil to the bolts and nuts during installation. However, this practice is not only wrong, but also brings certain hidden dangers to the driving safety of self loading mixer truck. After the bolt and nut are tightened, they have self-locking characteristics with each other. When the lubricant is applied, the self-locking coefficient between them becomes smaller and the self-locking performance decreases. When the self loading mixer truck runs at high speed, the bolts and nuts are easy to loosen or even fall off, resulting in a driving accident of the self loading mixer truck.
不要用水冲洗车身
Do not flush the body with water
内部夏天到了,常见私家车主们一边用水冲洗车身,一边用抹布擦拭,在此要提醒搅拌车司机的是:车身内部不要用水直接冲洗。因为驾驶室内地板胶垫的下面可不是“一马平川”,结构上的需要使驾驶室地板胶垫下面的凹槽、通孔非常多。用水冲洗后,要么沉积在凹槽内不易干燥,要么从通孔处流到自动上料搅拌车变速箱等部件上产生锈蚀。尤其是密封性能较好的自动上料搅拌车更不能用水直接冲洗车身内部。正确的方法是用湿抹布擦拭,但要避免积水。
When summer comes, it is common for private car owners to wash the body with water and wipe it with a rag. Here, we should remind the mixer driver that the interior of the body should not be washed directly with water. Because the bottom of the floor rubber pad in the cab is not "flat", there are many grooves and through holes under the floor rubber pad in the cab due to structural needs. After washing with water, it either deposits in the groove and is not easy to dry, or flows from the through hole to the gearbox and other parts of the automatic feeding mixer to produce corrosion. In particular, the automatic feeding mixer with good sealing performance cannot directly flush the interior of the vehicle body with water. The correct method is to wipe with a wet rag, but avoid ponding.
不同企业的冷却液不要混合使用
Do not mix different brands of coolant
谁都知道自动上料搅拌车发动机冷却液不足时应及时添加,但司机是否把不同企业的冷却液温在一起使用了呢?如果是,劝司机还是趁早把冷却液放掉,重新添加同一企业的冷却液。因为不同企业的冷却液其化学性能可能相差悬殊,比如对黑色金属有用的防腐剂,却常常对自动上料搅拌车铝制品有腐蚀作用;而适用于铝台金的防腐剂则对铁合金有害。由于不同企业的冷却液所用的防腐剂不同,所以不能混合使用。
Everyone knows that when the engine coolant of the automatic feeding mixer truck is insufficient, it should be added in time, but has the driver used the coolant temperature of different brands together? If so, advise the driver to drain the coolant as soon as possible and add the coolant of the same brand again. Because the chemical properties of different brands of coolants may vary greatly, such as preservatives useful for ferrous metals, but they often corrode the aluminum products of automatic feeding mixer trucks; The preservative suitable for aluminum Taijin is harmful to ferroalloy. Since different brands of coolant use different preservatives, they cannot be mixed.
电喷车启动时不要踩油门
Do not step on the accelerator when starting the EFI vehicle
启动自动上料搅拌车发动机前踩几脚油门,是许多驾驶员的习惯,尤其是在冬季冷车启动时。但这种启动方法却不适用于电喷轿车。装有电控喷油装置的自动上料搅拌车发动机与普通化油器式发动机不同,它的喷油控制装置能根据发动机的温度、工况自动调整供油量,使自动上料搅拌车发动机顺利启动,即在冷车启动时,喷油控制装置能自动增加供油量。所以,自动上料搅拌车发动机启动时,没有必要踩油门,更不要在启动前连续急踩,否则反而使自动上料搅拌车发动机启动不好。
It is the habit of many drivers to step on the accelerator before starting the engine of the automatic feeding mixer, especially when the vehicle is started cold in winter. However, this starting method is not suitable for EFI cars. The engine of the automatic feeding mixer equipped with the electronic control fuel injection device is different from the ordinary carburetor engine. Its fuel injection control device can automatically adjust the fuel supply according to the engine temperature and working conditions, so that the engine of the automatic feeding mixer can start smoothly, that is, when the cold vehicle starts, the fuel injection control device can automatically increase the fuel supply. Therefore, it is not necessary to step on the accelerator when starting the engine of the automatic feeding mixer, let alone continuously step on it before starting, otherwise the engine of the automatic feeding mixer will not start well.

截屏,微信识别二维码