自动上料搅拌车是一种用于工程的大型设备，所以操作人员的是要关注的一方面，当然要保障人身，要做的事情便是在用车前对设备各部件进行一个检查，以免有什么问题在使用中出现。

　　Automatic feeding mixer is a kind of large equipment for engineering, so the safety of the operator is the one to focus on, of course, to protect personal safety, the first thing to do is to check each part of the equipment before the car, so as not to have any problems in use.

　　做好措施，防止装料的搅拌车坏在路上。启动自上料搅拌车前，要先检查机油、润滑油和冷却水等物料是否充足，及时进行添加。车子启动后，低速旋转罐体，绕车一周检测胎压，防止有漏气车胎，用工具拿掉卡在轮胎中石子等杂物。

　　Take safety measures to prevent the mixing truck from breaking down on the road. Before starting the mixing vehicle, check whether the oil, lubricating oil and cooling water are sufficient and add them in time. After the car starts, rotate the tank at low speed, detect tire pressure around the car, prevent a leaky tire, remove the stone and other debris stuck in the tire with tools.

　　其次检验灯光是否正常，务必保证照着轮胎边缘，防止被工地堆放的钢筋杂物割伤。清理干净后视镜和窗户玻璃，司机保持清晰开阔视野，以应对工地的复杂工况场景。

　　Next check whether the light is normal, be sure to ensure that according to the tire edge, to prevent the site stacked steel debris cut. Clean the rearview mirror and window glass, and the driver keeps a clear and open vision to cope with the complex working scene of the construction site.

　　准备足够的水和减水剂。水可以应对混凝土物料干燥无法卸料的情况，减水剂也是同理，防止闷罐。启动搅拌车时确保搅拌罐处于静止状态。发动机启动时罐子如果处于高速旋转状态，瞬间的力会非常大，容易使减速机磨损，降低使用寿命。

　　Prepare plenty of water and water reducing agent. Water can cope with the dry concrete material can not discharge the situation, water-reducing agent is the same, to prevent stuffy pot. Make sure the tank is stationary when starting the mixer. If the tank is in a high-speed rotation state when the engine starts, the instantaneous force will be very large, which is easy to wear the reducer and reduce the service life.

　　另外，自动上料搅拌车一般露天停放，装料前先将罐里的积水和树叶之类的杂物排出，以免影响混凝土质量。装完料要记得冲洗进料斗，洗完后要关掉水箱进气口，打开水箱排气口排掉气体，因为气压下，水管连接不好的地方，容易渗水，影响其他车辆的。再次检查轮胎是否卡有石子铁钉等杂物，使用工具及时清理，因为停车时轮胎与地面接触的地方是检查不到的。

　　In addition, the automatic feeding mixer is generally parked in the open air, and the water and leaves in the tank will be discharged before loading, so as not to affect the quality of concrete. After loading the material, remember to wash the hopper. After washing, turn off the water tank inlet and open the exhaust port of the water tank to drain the gas, because under the pressure, the water pipe connection is not good, easy water seepage, affecting the safety of other vehicles. Check again whether the tire is stuck with stones, nails and other sundries, use tools to clean up in time, because the parking tire and the ground contact place is not checked.

　　总之，要想的运行自动上料搅拌车，就需要操作人员做好检查工作，尤其是检查设备各部件是否正常，当确认设备各部均属完好时，方可起动设备进行工作。更多设备相关内容就来网站http://www.jfhntjbj.com看看吧。

　　In short, in order to run the automatic feeding mixer safely, it is necessary for the operator to do a good job of checking the work, especially to check whether the parts of the equipment are normal. When confirming that all parts of the equipment are in good condition, the equipment can be started to work. For more information about devices, visit http://www.jfhntjbj.com.