In the process of operating the automatic feeding mixer, if the car stalls, what should we do? The following small automatic mixer for you to introduce in detail the following on the flameout of our solutions?

1、确定油路畅通

1. Make sure the oil circuit is smooth

确定油路畅通，柴油机供给系统没有空气后，可拆开油泵盖板，板动操纵手柄，拨动油泵拉杆，看拉杆是否灵活和柱塞弹簧是否断裂。

After confirming that the oil circuit is smooth and there is no air in the diesel engine supply system, the cover plate of the oil pump can be disassembled, the control handle can be moved, and the pull rod of the oil pump can be pulled to see whether the pull rod is flexible and whether the plunger spring is broken.

在自动搅拌车拉杆灵活和柱塞弹簧没断的情况下，可启动柴油机中速运转10分钟，还有断火现象时，可用一只铜榔头轻轻敲击输油泵大螺帽，一边敲一边听柴油机声音，如果声音不正常，说明输油泵活塞和推杆发卡，进行修理或更换。

Under the condition that the pull rod of the automatic feeding mixer truck is flexible and the plunger spring is not broken, the diesel engine can be started to run at medium speed for 10 minutes. In case of fire interruption, a copper hammer can be used to gently tap the big nut of the oil delivery pump and listen to the sound of the diesel engine. If the sound is abnormal, the piston and push rod of the oil delivery pump are jammed and repaired or replaced.

2、检查喷油器

2. Check the fuel injector

拆下喷油器总成，转动曲轴数圈，即有水喷出，说明缸盖，缸体有裂纹或砂眼，遇到这种情况时，可向用户解释或向自动上料搅拌车公司反映。低压油流畅通后，可用手压泵排除油路中的空气，打开泵头放气螺钉，直到没有气泡时，方可上紧放气螺钉。

Remove the fuel injector assembly and rotate the crankshaft for several turns, which means that there are cracks or sand holes in the cylinder head and cylinder block. In this case, you can explain to the user or report to the automatic feeding mixer company. After the low-pressure oil flow is smooth, the air in the oil circuit can be removed by hand pump, and the air release screw at the pump head can be opened until there is no bubble.

3、油嘴的不雾化

3. Non atomization of nozzle

油嘴不雾化，油泵柱塞弹簧和弹簧座断裂，卡死不工作，或是柴油内有水。拆下油嘴总成检查开启压力和雾化，如果油嘴总成正常，可让用户用干净柴油装入壶中用油路旁接法进行试验。打开自动上料搅拌车油箱开关，拆下输油泵进油管，看油流情况，如果油流很快，说明正常，如果油流时断时续查油路。

The oil nozzle is not atomized, the plunger spring and spring seat of the oil pump are broken, stuck and do not work, or there is water in the diesel oil. Remove the nozzle assembly to check the opening pressure and atomization. If the nozzle assembly is normal, the user can fill the pot with clean diesel oil and conduct the test with the oil way side connection method. Turn on the oil tank switch of the automatic feeding mixer, remove the oil inlet pipe of the oil delivery pump and check the oil flow. If the oil flow is fast, it indicates that it is normal. If the oil flow is intermittent, continue to check the oil circuit.

以上就是关于自动搅拌车的相关知识介绍，希望能够帮助到大家。如需了解更多相关资讯，请继续关注我们网站http://www.jfhntjbj.com，后续将呈现更多精彩的内容。

The above is about the automatic feeding mixer related knowledge introduction, I hope to help you. For more information, please stay tuned to our website http://www.jfhntjbj.com , more wonderful content will be presented later.