The automatic feeding mixer engine is playing a key role in the whole control application process, and many friends are familiar with many shortcomings of the automatic feeding mixer engine. Therefore, many troubles of the automatic feeding mixer machine are formed by our own shortcomings. Accurate maintenance and familiarity have a good effect on the application life of the vehicle.

一些自动上料搅拌车驾驶员认为发动机温度居下没有低,所以自发撤除发动机恒温器,冷却液只能除夜周期,不克不及调解冷却强度,所以发动机经常正在高温条件下工作,导致权利的损失,磨损,燃料消费增加,等等。事实上,高温对发动机有害。应该正在一样平常温度限定自动上料搅拌车的应用范例,以确保发动机的应用寿命。

Some auto feeding mixer drivers think that the engine temperature is not low, so they remove the engine thermostat spontaneously. The coolant can only adjust the cooling cycle, but can not adjust the cooling intensity. Therefore, the engine is often working under high temperature conditions, resulting in the loss of rights, wear loss, increased fuel consumption, and so on. In fact, high temperature is harmful to the engine. Should be the same as the usual temperature limit automatic feeding mixer application example, in order to ensure the service life of the engine.

带松没有是更好。皮带太松不只会让它舒展或损坏,收缩皮带的应用寿命,并且借由于压力太除夜,导致自动上料搅拌车发电机轴,泵轴曲折变形战轴承初期损伤。宽松的自动上料搅拌车发动机电扇皮带应相符技巧要求,一样平常一样平常带装配偏差10到15毫米为宜。

It's better not to have loose belts. Too loose belt will not only make it stretch or damage, shrink the service life of the belt, but also lead to automatic feeding mixer generator shaft, pump shaft bending deformation and bearing initial damage due to too much pressure. Loose automatic feeding mixer engine fan belt should meet the technical requirements, as usual with assembly deviation of 10 to 15 mm is appropriate.

很多司机晓得,车子方才开端,如果发动机转速过下会损害发动机由于滑腻不良。但是,很少有人晓得如果应用闲置很少一段时间升温,由于低速，自动上料搅拌车油泵不克不及迅速按下润滑油为全体滑腻表面,发动机全体挪动部件将正在干摩擦或半干摩擦条件下工作。

Many drivers know that the car has just started, if the engine speed is too low, it will damage the engine due to poor lubrication. However, few people know that if the application is idle for a short period of time, due to the low speed, the automatic feeding mixer oil pump cannot quickly press the lubricating oil to all the greasy surfaces, and all the moving parts of the engine will be working under dry friction or semi dry friction conditions.

同时由于高温燃油雾化没有良,使已燃烧的燃料进入曲轴箱,洗失落气缸壁的油膜,加速零件磨损。是以,正在高温条件下,自动上料搅拌车发动机启动几秒钟后,应该改良怠速疾速加热,提高发动机滑腻条件。

At the same time, due to the poor atomization of high-temperature fuel, the burned fuel enters the crankcase and washes out the oil film on the cylinder wall, which accelerates the wear of parts. Therefore, under the high temperature condition, after the automatic feeding mixer engine starts for a few seconds, it should improve the idling speed heating to improve the engine greasy condition.