欢迎来到中科聚峰机械有限公司!

24小时服务热线:

400-879-1999

点击拨打服务热线:400-879-1999
当前位置:首页>新闻中心>行业新闻搅拌车分析清洗搅拌筒应该这注意什么?

搅拌车分析清洗搅拌筒应该这注意什么?

来源:http://www.jfhntjbj.com/ 日期:2021-07-12 发布人:admin
概述:很多人对于我们的1 0方自动上料搅拌车已经有了一些了解,而且也为大家介绍过,而今天小编将给大家介绍 "清洗搅拌筒应该这注意什么?希望能帮助到大家
很多人对于我们的1.0方自动上料搅拌车已经有了一些了解,而且也为大家介绍过,而今天小编将给大家介绍"清洗搅拌筒应该这注意什么?希望能帮助到大家.
Many people already have some understanding of our 1.0 square automatic feeding mixer, and they have also introduced it to you. Today, Xiaobian will introduce "what should we pay attention to when cleaning the mixing drum? Hope to help you
1、在施工现场卸料完毕后,应立即用搅拌车随带的软管冲洗进料斗、出料斗、卸料溜槽等处,粘附在车身各处的污泥及混凝土。在返回搅拌站的途中,应向搅拌筒内注150---200L水以清洗筒壁及叶片粘结的混凝土残渣。
1. After unloading at the construction site, the feeding hopper, discharging hopper, discharging chute, etc. shall be washed immediately with the hose attached to the mixer truck to remove the sludge and concrete adhered to the vehicle body. On the way back to the mixing plant, 150-200l water should be injected into the mixing drum to clean the concrete residue bonded on the wall and blades of the drum.
2、每天工作结束后,司机应负责向搅拌筒内注入清水并高速(14—18转/分)旋转5—10分钟,然后将水排去,以保证筒内清洁。用高压水清洗搅拌筒各个部分时,应注意避开仪表及操纵杆等部位。压力水喷嘴与车身油漆表面间的距离不得小于40厘米。
2. At the end of each day's work, the driver shall be responsible for injecting clean water into the mixing drum and rotating at high speed (14-18 RPM) for 5-10 minutes, and then discharging the water to ensure the cleanness of the drum. When using high-pressure water to clean each part of the mixing drum, attention should be paid to avoid the instrument and control rod. The distance between the pressure water nozzle and the body paint surface shall not be less than 40 cm.
3、搅拌筒内外积污及残存的混凝土渣块时,以及在机修人员进入筒内进行检修和焊补作业时,需先关闭汽车发动机,使搅拌筒完全停止转动。在机修人员进入筒内工作期间,必须保证拌筒内通风良好,空气新鲜,无可然气体及有害灰尘,氧气供应充足。在筒内使用电动工具操作时,操作人员必须有良好的绝缘保护。
3. When removing the dirt and residual concrete slag inside and outside the mixing drum, and when the maintenance personnel enter the drum for maintenance and welding repair, it is necessary to turn off the automobile engine to stop the mixing drum completely. During the working period, the maintenance personnel must ensure that the mixing cylinder is well ventilated, the air is fresh, there is no natural gas and harmful dust, and the oxygen supply is sufficient. When using electric tools in the cylinder, operators must have good insulation protection.
4、工作时,不得将手伸入旋转的搅拌筒内,严禁将手伸入主卸料溜槽和加长卸料溜槽的连接部位清洗,清洗搅拌筒应该这注意什么?以免发生事故。
4. When working, do not put your hand into the rotating mixing drum. It is strictly forbidden to put your hand into the connection part of the main discharge chute and the extended discharge chute for cleaning. What should you pay attention to when cleaning the mixing drum? To avoid accidents.

截屏,微信识别二维码