1. When removing the tire, stop in a clean, flat, dry, hard and oil-free air to avoid sand, debris, etc. falling on the inner wall of the outer tire or adhering to the outer surface of the inner tire to damage the inner tire, and avoid oil adhering to the tire and corroding the tire.

2、拆卸轮胎应由有实践经历的人员操作或指导，切不可乱敲乱打，以免使轮圈产生锐边、凹痕、龟裂等缺陷，并要坚持轮圈的清洁，避免锈蚀损坏。

2. The removal of tires shall be operated or guided by personnel with practical experience. It is not allowed to knock or beat randomly, so as to avoid sharp edges, dents, cracks and other defects of the rim, and the rim shall be kept clean to avoid corrosion and damage.

3、只能运用专用工具和撬棒停止拆装，停止运用螺丝刀之类的锋利工具。

3. Only use special tools and crowbars to stop disassembly and assembly, and stop using sharp tools such as screwdrivers.

4、拆卸办法。放掉轮胎中的空气，应用气门帽将气门芯拧出，打下气门嘴固定螺母，用双脚踩踏或用锤子重击外胎侧面，使轮胎的胎圈脱离轮圈边缘进入轮辋中部凹槽内，将气门嘴推进轮圈内。在气门嘴左近将撬棒插入胎缘轮辋之间，将胎缘撬起。

4. Disassembly method. Release the air in the tire, screw out the valve core with the valve cap, knock down the valve fixing nut, tread with both feet or hit the side of the outer tire with a hammer to make the tire bead separate from the rim edge and enter the groove in the middle of the rim, and push the valve into the rim. Insert a pry bar near the valve into the tire rim and pry up the tire rim.

同时在撬胎棒的对面用力紧缩外胎胎壁，使外胎尽量移向轮辋中部凹槽内，行将撬出的部位尽量放松。然后将二根撬胎棒插入一根撬胎棒左近，顺着轮辋逐步地将胎缘撬出，尚未撬出的局部，应尽量压向轮辋直径小的凹槽部。当轮胎的一边被撬出后，便很容易地取出内胎及外胎另一边。

At the same time, tighten the outer tire wall on the opposite side of the tire prying rod to move the outer tire to the groove in the middle of the rim as much as possible, and relax the part to be pried out as much as possible. Then insert two tire prying rods to the left of one tire prying rod, and gradually pry out the tire rim along the rim. The parts that have not been pryed out shall be pressed to the groove with small rim diameter as far as possible. When one side of the tire is pried out, it is easy to take out the inner tire and the other side of the outer tire.

5、假如搅拌车轮胎运用日久，外胎锈死在辋圈内而不容易取下时，能够将轮胎平放在洁净的空中上，用撬棒在胎口与辋圈之间撬开一定间隙，在辋圈与外胎的分离部倒些肥皂水或清水，并用铁锤沿l轮圈外侧稍加锤击，使水在振动的过程中从缝隙处渗入生锈面，待浸透后（约2～3min），外胎便容易拆下来。

5. If the mixer tire is used for a long time and the outer tire is rusted in the rim ring and is not easy to remove, the tire can be placed flat in the clean air, pry a certain gap between the tire orifice and the rim ring with a crowbar, pour some soapy water or clean water at the separation part between the rim ring and the outer tire, and hammer slightly along the outside of the L rim with a hammer to make the water penetrate into the rusty surface from the gap during vibration, After soaking (about 2-3 minutes), the outer tube can be easily removed.

阅读了本篇文章你是否对全自动上料搅拌一体车的轮胎的拆卸方法有了一定的了解了呢？希望本篇文章能对你有所帮助。

After reading this article, do you have a certain understanding of the disassembly method of the tire of the fully automatic feeding and mixing integrated vehicle? I hope this article can help you.