Some users report that there will be oil leakage in the use of their automatic feeding mixer. In fact, if the oil leakage problem is not dealt with in time, it is likely to cause early damage to parts, so today we will first find the cause of oil leakage, so as to be able to do a good job in responding to measures.

　　自动上料搅拌机上的各种螺母是否拧紧。有时，自动上料搅拌机的漏油是因为车辆的连接螺母松动。

　　All nuts on automatic feeding mixer are tight. Sometimes oil leaks from automatic feeder mixers are caused by loose coupling nuts on vehicles.

　　自动上料搅拌机漏油也可能是密封材料长期使用后过度磨损、老化变质、变形失效等原因。

　　Oil leakage of automatic feeding mixer may also be the cause of excessive wear, aging, deformation and failure of sealing materials after long-term use.

　　拧紧螺母的拧紧力不均、滑动螺纹断裂或松动脱落也会导致工作失败。如果垫片太松而未拧紧，垫片会泄漏；如果拧得太紧，螺丝孔附近的金属会突出或螺纹扭曲而导致漏油。

　　Uneven tightening force of tightening nut, fracture or loose falling off of sliding thread will also lead to work failure. If the gasket is too loose and not tightened, the gasket will leak; If the screw is tightened too tightly, metal near the screw hole can protrude or twist the thread, causing oil leakage.

　　装配是否不当，表面是否不干净，垫片是否损坏、移位或未按操作规程安装。更换联管螺母，用磨削法锥面密封，压紧螺母密封。如果材料、生产质量和安装不符合技术规范，将无法密封和防止泄漏，甚会发生事故。

　　Whether the assembly is improper, whether the surface is not clean, whether the gasket is damaged, displaced or not installed according to the operating procedure. Replace the union nut, solve the cone sealing with grinding method, and solve the sealing by pressing the nut. If the material, production quality and installation do not meet the technical specifications, it will not be able to seal and prevent leakage, and even accidents will occur.

　　是否是轮毂油。结果，套管内温度升高，油气充满整个空间而无法排出，使套管内压力增加，润滑油消耗量增加，更换周期缩短。

　　Is it hub oil? As a result, the temperature in the casing rises and the oil and gas fill the space without being discharged, increasing the pressure in the casing, increasing the consumption of lubricating oil and shortening the replacement cycle.

　　自动上料搅拌机上的许多运动部件会因安装不当而产生错位。轮毂轴承和腔内润滑脂过多，或油品包装不当，质量差，老化失效；频繁制动导致轮毂温度过高；轴螺母松动等会导致轮毂甩油，漏油应及时更新。

　　Many moving parts on the automatic feeding mixer may be misplaced due to improper installation. Hub bearing and grease in the cavity is too much, or oil packaging is improper, poor quality, aging failure; Frequent braking results in high hub temperature; Axle nut loosening will lead to hub oil dumping, oil leakage should be updated in time.

　　在这里我们排查了几个方面的漏油原因，当然如果您在使用自动上料搅拌车工作时还发生了别的问题而您找不到原因时，欢迎随时来http://www.jfhntjbj.com网站咨询！