自动上料搅拌车是现在比较常用的大型运输车辆，它工作效率高，运输速度快，因此搅拌车的轮胎充气是很重要的，下面就说说轮胎充气注意事项。

Automatic loading mixer truck is a commonly used large-scale transportation vehicle now. It has high working efficiency and fast transportation speed. Therefore, tire inflation of mixer truck is very important. Here are the precautions for tire inflation.

1、搅拌车充气不要选择刚刚行驶过的时候进行充气，要等轮胎完全冷却后再充气，因为长时间行驶过的车辆轮胎温度较高，我们知道热胀冷缩原理，轮胎温度过高对气压是有一定的影响的，所以为了正确的判断气压情况，我们需要等轮胎温度冷却后再进行充气。

1. Don't choose to inflate the mixer when it has just been driven. Wait until the tires are completely cooled before inflating. Because the tires of vehicles that have been driven for a long time have a high temperature, we know the principle of thermal expansion and cold contraction. Too high tire temperature has a certain impact on the air pressure, so in order to correctly judge the air pressure, we need to wait until the tire temperature is cooled before inflating.

2、在轮胎充气前我们需要检查充气是否清洁，如果充气设备或周围环境不清洁，很容易有水分、油污、杂质等进入轮胎内，造成内胎橡胶变形变质或出现早期损坏现象。还有就是注意气门嘴的清洁，轮胎长期与地面接触，气门嘴上往往有泥土、灰尘等，在充气前我们需要将气门嘴清理赶紧，以防止杂质进入轮胎内，损坏轮胎。

2. Before inflation, we need to check whether the inflation is clean. If the inflation equipment or the surrounding environment is not clean, it is easy for moisture, oil, impurities, etc. to enter the tire, causing deformation and deterioration of the inner tube rubber or early damage. Also, pay attention to the cleaning of the valve. The tire is in long-term contact with the ground, and there are often mud, dust, etc. on the valve. Before inflation, we need to clean the valve quickly to prevent impurities from entering the tire and damaging the tire.

3、充气时尽量不要松动或取出自动上料搅拌车的气门芯，靠增大气压强行充气，以防造成气门嘴螺丝脱扣漏气。充气完毕后，应蘸水涂在气门嘴上，检查是否漏气，以便视情况拧紧或更换气门芯。充完气，还应配齐装紧气门嘴帽，防止泥沙等进入气门嘴内。

3. When inflating, try not to loosen or take out the valve core of the automatic feeding mixer truck, and forcibly inflate by increasing the air pressure to prevent the valve screw from tripping and air leakage. After inflation, dip water on the valve to check whether there is air leakage, so as to tighten or replace the valve core according to the situation. After gas filling, the valve cap should also be fully installed to prevent sediment from entering the valve.

要注意：

Note:

随着搅拌车成本的不断增加，搅拌车轮胎实际上成本很高，其驱动方式与轮胎磨损有很大的关系。良好而熟练的驾驶技术可以 减少搅拌车轮胎的磨损，延长轮胎使用寿命，提高驾驶 。我们无法控制价钱 ，因此如何减少磨损，保护轮胎使用周期更大 化是我们需要掌握的。

With the increasing cost of mixer truck, the cost of mixer truck tire is actually very high, and its driving mode has a great relationship with tire wear. Good and skilled driving skills can reduce the wear of mixer tires, prolong the service life of tires and improve driving. We can't control the price, so we need to know how to reduce wear and protect the tire's service life.

，胎压应达到标准。搅拌车驾驶员应按照要求给轮胎充气。当轮胎压力低于标准值时，轮胎胎肩磨损会增加。当轮胎压力高于标准值时，由于轮胎的接地面积减小，单位压力增大，从而使轮胎的中间磨损增加，同时，轮胎的刚度增加，并且车轮动负荷增大，胎体容易发生爆裂。

First, the tire pressure should meet the standard. The mixer driver shall inflate the tires as required. When the tire pressure is lower than the standard value, the tire shoulder wear will increase. When the tire pressure is higher than the standard value, because the grounding area of the tire decreases and the unit pressure increases, the middle wear of the tire increases. At the same time, the stiffness of the tire increases, and the dynamic load of the wheel increases, and the tire body is prone to burst.

此外在驾驶搅拌车时要注意，在夏季或高速行驶时，轮胎很容易过热，而压力却增加了。这时，驾驶员应停车以散热，严禁放气或水冷，以防止橡胶异常老化，造成损害。更多事项就来我们网站http://www.jfhntjbj.com咨询吧。

In addition, when driving a mixer truck, it should be noted that in summer or when driving at high speed, the tires are easy to overheat, but the pressure increases. At this time, the driver should stop to dissipate heat, and it is strictly forbidden to deflate or water-cooling, so as to prevent abnormal aging of rubber and damage. Come to our website for more information http://www.jfhntjbj.com Consult.