自上料搅拌车有时候会出现问题，是由于里面有很多的土渣没有清理干净，需要及时将内部的土渣清理出来，这样才能使它正常运行，接下来就教大家清理土渣的方法，希望能够给您帮助。

Sometimes there are problems with the self loading mixer, because there are a lot of soil residues in it that have not been cleaned. It is necessary to clean out the internal soil residues in time so that it can operate normally. Next, I will teach you how to clean the soil residues. I hope I can help you.

1、准备好紧急驱动软管，将自上料搅拌车熄火，卸下液压马达上的高压油管接头。

1. Prepare the emergency drive hose, turn off the self feeding mixer, and remove the high-pressure oil pipe connector on the hydraulic motor.

2、将救援车熄火，将其液压马达的高压油管卸下，并与故障车上的对应接头用紧急驱动软管相连。

2. Turn off the rescue vehicle, remove the high-pressure oil pipe of its hydraulic motor, and connect it with the corresponding connector on the failed vehicle with the emergency drive hose.

3、发动救援车，将其操纵手柄拨出料位置，故障车内的混凝土即被排出。

3. Start the rescue vehicle and turn its operating handle to the discharging position, and the concrete in the fault vehicle will be discharged.

4、紧急驱动完毕后，将驱动软管卸下，并恢复两车原状。

4. After the emergency drive is completed, remove the drive hose and restore the two vehicles to their original state.

5、还有一种简单点的方法就是在托轮和滚道之间放入木楔，控制搅拌筒的旋转，将发动机熄火，拆松液压马达的一根高压油管，搅拌筒可自由旋转，控制搅拌筒的旋转，使维修孔转到下部，然后打开维修孔，清理出筒内混凝土。混凝土排出完毕后，恢复搅拌车原状。

5. Another simple method is to put a wooden wedge between the supporting wheel and the raceway, control the rotation of the mixing drum, turn off the engine, and loosen a high-pressure oil pipe of the hydraulic motor. The mixing drum can rotate freely, control the rotation of the mixing drum, turn the maintenance hole to the lower part, and then drill the maintenance hole to clean the concrete in the drum. After the concrete is discharged, the mixer shall be restored to its original state.

自上料搅拌车的清洗过程：

Cleaning process of self feeding mixer:

1、每天的工作结束后，将搅拌罐内注入适量的水，并保持搅拌罐缓慢旋转；

1. After daily work, inject proper amount of water into the mixing tank and keep the mixing tank rotating slowly;

2、将自上料搅拌车水箱里的水加满，以保证清洗过程的水量充足；

2. Fill up the water in the water tank of the loading mixer to ensure sufficient water in the cleaning process;

3、向罐体内注水，注水过程中保持搅拌罐工作状态，以足够的水量保证洗掉搅拌罐内残存的混凝土；

3. Inject water into the tank, keep the mixing tank in working condition during the water injection, and ensure that the residual concrete in the mixing tank is washed off with sufficient water;

4、打开洗车泵，接好高压水枪（高端自上料搅拌车标配，有些厂家可能需要定制）；

4. Turn on the car washing pump and connect the high-pressure water gun (standard for high-end self feeding mixer, some manufacturers may need to customize);

5、仔细清洗罐体、进料口、出料口、车身等残留物料；

5. Carefully clean the residual materials such as tank body, feed port, discharge port and vehicle body;

6、确认没有水泥和混凝土结块后，将搅拌罐内污水放掉。

6. After confirming that there is no cement and concrete caking, drain the sewage in the mixing tank.

以上就是自上料搅拌车清洗土渣的方法，无论是选择哪种方法都要注意，当然平日使用中的维护保养事项是不能少的，您可以来我们网站http://www.jfhntjbj.com进行详情了解。

The above is the method of cleaning soil slag by self loading mixer. No matter which method you choose, you should pay attention to safety. Of course, the maintenance items in daily use are indispensable. You can visit our website http://www.jfhntjbj.com For details.