欢迎来到中科聚峰机械有限公司!

24小时服务热线:

400-879-1999

点击拨打服务热线:400-879-1999
当前位置:首页>新闻中心>行业新闻自动搅拌车变速器油质的检测方式

自动搅拌车变速器油质的检测方式

来源:http://www.jfhntjbj.com/ 日期:2022-10-19 发布人:admin
概述:在设备实际操作运行过程中,自动搅拌车的变速器是一个非常重要的部件。因此,我们在使用过程中对其油质需要有一定的检测工作,那么我们具体
在设备实际操作运行过程中,自动搅拌车的变速器是一个非常重要的部件。因此,我们在使用过程中对其油质需要有一定的检测工作,那么我们具体应该怎么进行操作呢?下面小编为您讲解。
During the actual operation of the equipment, the transmission of the automatic mixer is a very important component. Therefore, we need to have some inspection work on the oil quality during the use, so how should we operate? The following section explains it for you.
1、将自动搅拌车停放在水平地面上,并拉紧手制动。
1. Park the automatic mixer on the level ground and tighten the hand brake.
2、让发动机怠速运转数分钟。
2. Allow the engine to idle for a few minutes.
3、踩住制动踏板,将操纵手柄拨倒挡、前进挡等位置,并在每个挡位上停留几秒钟,使液力变矩器和所有换挡执行元件中都充满液压油。后将操纵手柄拨停车挡位置。
3. Step on the brake pedal, move the joystick to reverse gear, forward gear, etc., and stay in each gear for a few seconds to make the hydraulic torque converter and all shift actuating elements full of hydraulic oil. Then, turn the joystick to the parking position.
4、从加油管内拨出自动变速器油尺,将擦干净的油尺全部插入加油管再拔出,检查油尺上的油面高度。
4. Pull out the automatic transmission oil dipstick from the oil filler pipe, insert the cleaned oil dipstick into the oil filler pipe and then pull it out, and check the oil level on the oil dipstick.
一般搅拌车自动变速器油的油位检查可以通过油尺来查看,检查油位的正确步骤是:
Generally, the oil level of the automatic transmission oil of the mixer can be checked through the dipstick. The correct steps for checking the oil level are:
自动搅拌车
①行驶被检车辆,使发动机和变速器达到正常工作温度(50一90℃);
① Drive the inspected vehicle to make the engine and transmission reach normal operating temperature (50-90 ℃);
②将车辆停放于水平路面,采取驻车制动,将换挡手柄推N位后启动发动机;
② Park the vehicle on a level road, apply the parking brake, push the gear shift handle to the N position and start the engine;
③使发动机保持怠速运转,将操纵手柄依次推人所有位置,并在每一个位置上停留片刻,后将手柄推P位;
③ Keep the engine running at idle speed, push the operating handle to all positions in turn, stay at each position for a moment, and then push the handle to position P;
④从自动变速器加油管中拉出油尺,用干净的纸或布擦拭干净后再将油尺放回套管,注意油尺插人要到位;
④ Pull out the oil dipstick from the oil filler pipe of the automatic transmission, wipe it with clean paper or cloth, and then put the oil dipstick back into the sleeve. Note that the oil dipstick must be inserted in place;
⑤拉出油尺检查油位是否在正确位置,液面过高或过低都不允许。
⑤ Pull out the dipstick to check whether the oil level is at the correct position. It is not allowed to have too high or too low liquid level.
在对自动搅拌车变速器进行检查或故障诊断前,先要对变速器油面和油质进行检查。把选挡手柄放在P位,将发动机在怠速时少运转数分钟,油液达到正常工作温度,搅拌车须停放在水平路面上,这样才能确保在差速器和变速器之间的油面高度正常、稳定。
Before the inspection or fault diagnosis of the automatic mixer truck transmission, check the transmission oil level and quality. Put the gear selection handle at P position, and run the engine at idle speed for at least a few minutes. The oil reaches the normal operating temperature. The mixer must be parked on a level road, so as to ensure that the oil level between the differential and the transmission is normal and stable.
自动搅拌车变速器油质的检测方式就讲解到这里了,您对此有什么想咨询的问题或者有什么需求可以随时来我们网站http://www.jfhntjbj.com了解!
This is the end of the inspection method for the transmission oil quality of the automatic mixer. If you have any questions or needs, you can come to our website at any time http://www.jfhntjbj.com Understand!

截屏,微信识别二维码