搅拌一体车价格

24小时服务热线:

15053524111

点击拨打服务热线:15053524111
热门关键词: 自动搅拌车价格,自动上料搅拌车,搅拌一体车
当前位置:首页>自上料搅拌车技术问答>常见问题>自动上料搅拌车在自重力压力调节的的方法和常见问题

自动上料搅拌车在自重力压力调节的的方法和常见问题

来源:http://www.jfhntjbj.com/ 日期:2020-12-09 发布人:guanli 浏览:
TAG:自动搅拌车,自动上料搅拌车,搅拌一体车
概述:查看液压泵是否可以输出液压油。假如是没有输出液压油的新型液压泵,则泵体或许存在铸造缺陷,因此吸入室和液压室相连,油压下降,而且制造商应及时替换。
自动上料搅拌车操作时?调理压力问题?
How to adjust the pressure during the operation of the automatic feeding mixer?
1.查看液压泵是否可以输出液压油。假如是没有输出液压油的新型液压泵,则泵体或许存在铸造缺陷,因此吸入室和液压室相连,油压下降,而且制造商应及时替换。假如不是新的液压泵,而且没有液压油输出,则或许无法正确操作泵,而且零件或许会严峻磨损或损坏。
1. Check whether the hydraulic pump can output hydraulic oil. If it is a new type of hydraulic pump without hydraulic oil output, the pump body may have casting defects, so the suction chamber is connected with the hydraulic chamber, the oil pressure drops, and the manufacturer should replace it in time. If it is not a new hydraulic pump and there is no hydraulic oil output, the pump may not be operated correctly and the parts may be severely worn or damaged.
自动上料搅拌车
2.假如液压泵有油输出,请查看安全阀是否正常作业。假如反常,则压力油回路中的阀或许由于其他原因被污染或堵塞,而且处于回油方位,导致压力油回路与溢流回路短路,或许管接头或许松动或受压。油路中的某些阀泄漏严峻,或许液压缸和液压马达的密封件损坏,导致严峻泄漏。
2. If the hydraulic pump has oil output, please check whether the safety valve works normally. If it is abnormal, the valve in the pressure oil circuit may be contaminated or blocked due to other reasons, and it is in the oil return position, resulting in a short circuit between the pressure oil circuit and the overflow circuit, or the pipe joint may be loose or pressurized. The leakage of some valves in the oil circuit is serious. Maybe the seals of hydraulic cylinder and hydraulic motor are damaged, which leads to severe leakage.
3.假如液压泵的输出流量随压力的增加而明显下降,但压力未到达规定值,则是由于液压泵磨损后间隙的增加所致。
3. If the output flow of the hydraulic pump decreases obviously with the increase of the pressure, but the pressure does not reach the specified value, it is due to the increase of the clearance after the wear of the hydraulic pump.
4.假如自动上料搅拌车的整个液压体系可以树立正常压力,而且某些管线或液压缸(或液压马达)中没有压力,则或许是由于管线,小孔或节流阀,方向阀等引起的。进行封锁时,应逐个查看压力和机油以找出原因并进行整理。
4. If the whole hydraulic system of the automatic feeding mixer can establish normal pressure, and there is no pressure in some pipelines or hydraulic cylinders (or hydraulic motors), it may be caused by pipelines, small holes or throttle valves, directional valves, etc. When blocking, check the pressure and oil one by one to find out the cause and sort it out.
自动上料搅拌车压力调理介绍就是这些,希望对你有帮助。如需更多的精彩内容请关注公司网站:http://www.jfhntjbj.com
This is the introduction of pressure regulation of automatic feeding mixer. I hope it can help you. For more exciting content, please visit our website: http://www.jfhntjbj.com

截屏,微信识别二维码

微信号:

点击微信号复制,添加好友

 打开微信