欢迎来到中科聚峰机械有限公司!

24小时服务热线:

400-879-1999

点击拨打服务热线:400-879-1999
当前位置:首页>新闻中心>常见问题安装搅拌车的用例限制在环境温度范围内

安装搅拌车的用例限制在环境温度范围内

来源:http://www.jfhntjbj.com/ 日期:2020-12-28 发布人:admin
概述:一些特定的自动上料搅拌车司机认为发动机温度不低,因此发动机恒温器将被自动移除,而冷却液只能从夜间循环中移除。
一些特定的自动上料搅拌车司机认为发动机温度不低,因此发动机恒温器将被自动移除,而冷却液只能从夜间循环中移除。
Some specific automatic feeding mixer drivers believe that the engine temperature is not low, so the engine thermostat will be automatically removed, and the coolant can only be removed from the night cycle.
由于无法调节冷却强度,因此发动机通常在高温条件下运行。这会导致磨损并增加燃油消耗。实际上,高温对发动机有害。为了确保发动机的使用寿命,应将安装自动上料搅拌车的用例限制在环境温度范围内。
Because the cooling intensity cannot be adjusted, the engine usually runs at high temperature. This causes wear and increases fuel consumption. In fact, high temperature is harmful to the engine. In order to ensure the service life of the engine, the use case of installing the automatic feeding mixer should be limited to the ambient temperature range.
橡皮筋很好。如果皮带太松,不仅会拉伸并损坏皮带,缩短皮带的使用寿命,而且过大的压力会自动加载并扭曲搅拌器的发电机轴和泵轴,从而损坏搅拌器。为了满足技术要求,必须松开自动上料搅拌车的风扇皮带。建议的组装偏差为10-15毫米。
The rubber band is very good. If the belt is too loose, it will not only stretch and damage the belt, shorten the service life of the belt, but also the excessive pressure will automatically load and twist the generator shaft and pump shaft of the agitator, thus damaging the agitator. In order to meet the technical requirements, the fan belt of the automatic feeding mixer must be loosened. The recommended assembly deviation is 10-15mm.
许多驾驶员知道这辆车刚刚起步。同样,如果发动机转速过低,则由于打滑不良会损坏发动机。
Many drivers know that the car is just starting. Similarly, if the engine speed is too low, the engine will be damaged due to poor slip.
但是,大多数人都知道自动上料搅拌车中的油泵无法快速润滑光滑表面上的润滑剂,因为由于加热速度较慢,它们将在短时间内处于闲置状态。
However, most people know that the oil pump in the automatic feeding mixer can not quickly lubricate the lubricant on the smooth surface, because they will be idle for a short time due to the slow heating speed.
同时,由于高温燃油雾化不足,燃烧的燃油进入曲轴箱,冲刷了气缸壁上的油膜,并加速了零件的磨损。因此,在自润滑发动机启动后几秒钟的高温条件下,有必要改善空转加热并提高发动机滑移率。
At the same time, due to the lack of high temperature fuel atomization, the burning fuel enters the crankcase, washes the oil film on the cylinder wall, and accelerates the wear of parts. Therefore, it is necessary to improve the idling heating and increase the slip ratio of the self-lubricating engine in the high temperature condition of a few seconds after starting.
自动上料搅拌车错误使用发动机的影响就是这些,你了解了吗?如果还有不明白的地方,可以关注:http://www.jfhntjbj.com会有在线客服为您进行解答。
This is the impact of the wrong use of the engine of the automatic feeding mixer. Do you understand? If you still don't understand, you can pay attention to: http://www.jfhntjbj.com There will be online customer service to answer for you.

截屏,微信识别二维码