欢迎来到中科聚峰机械有限公司!

24小时服务热线:

400-879-1999

点击拨打服务热线:400-879-1999
当前位置:首页>新闻中心>常见问题搅拌车的筒体直径有什么要点?

搅拌车的筒体直径有什么要点?

来源:http://www.jfhntjbj.com/ 日期:2021-03-05 发布人:admin
概述:筒体直径选择必须要考虑到,筒体倾斜角的大小,这也是个关重要的参数之一,因为倾斜角决定的筒体的位置,进而影响整个车的,如果不合理,那么侧翻也就很容易发生。如果
筒体直径选择必须要考虑到,筒体倾斜角的大小,这也是个关重要的参数之一,因为倾斜角决定的筒体的位置,进而影响整个车的,如果不合理,那么侧翻也就很容易发生。如果倾斜角过大,而筒直径不相对减小的话那么就容易侧翻。
The selection of the cylinder diameter must take into account the size of the cylinder tilt angle, which is also one of the most important parameters, because the tilt angle determines the position of the center of gravity of the cylinder, and then affects the center of gravity of the whole car. If the center of gravity is unreasonable, then rollover is easy to occur. If the inclination angle is too large and the diameter of the cylinder is not relatively reduced, it is easy to roll over.

我们需要看一下自动上料搅拌车所使用的地段,不同的地段也是需要配备不一样的搅拌罐的。地势平坦的罐可以做的容量相对大一点,筒直径可以相对大一些,地势相对复杂的要做的筒直径相对小一些,这样是为了让自动上料搅拌车更加的稳定,充分保障驾驶员的,提高环境适应能力。
We need to look at the sections used by the automatic feeding mixer. Different sections also need to be equipped with different mixing tanks. The capacity of the tank with flat terrain can be relatively large, the diameter of the cylinder can be relatively large, and the diameter of the cylinder with relatively complex terrain can be relatively small. This is to make the automatic feeding mixer more stable, fully guarantee the safety of the driver, and improve the environmental adaptability.
对于销往世界各地的自动上料搅拌车来说,我们做车之前都会对该地区的路况进行系统分析,进而得出结论开始做车。的追求,使我们的对产品的要求,因此来中科聚峰厂家,是您购车的不二选择。
For the automatic feeding mixer sold all over the world, we will make a systematic analysis of the road conditions in this area before we make the car, and then draw a conclusion to start making the car. The pursuit of perfection makes us meet the requirements of our products. Therefore, coming to Zhongke Jufeng factory is your best choice to buy a car.
自动上料搅拌车是由一系列精密的系统构成。所以说,各个环节之间是相互制约,相互合作共同完成搅拌车的正常运作。
Automatic feeding mixer is composed of a series of precise systems. Therefore, each link restricts and cooperates with each other to complete the normal operation of the mixer.
因此,我们要看一下底盘的配置,主要看底盘的动力、外形尺寸、车头质量等一系列参数,这些参数就像人的形体,而搅拌罐就像是人的衣服。
Therefore, we need to look at the configuration of the chassis. It mainly depends on a series of parameters such as the power of the chassis, the overall dimensions, and the mass of the front of the car. These parameters are like a person's body, while the mixing tank is like a person's clothes.

截屏,微信识别二维码